KM3NeT - Working Package 3 - Meeting on Optical Modules

9 Apr 2008, 10:00 → 11 Apr 2008, 16:00 Europe/Rome

Istituto Nazionale di Fisica Nucleare - Sezione di Genova

The aim of the meeting is to have a review of the current activity and to begin to define the procedure that we will use to definitely define the design of the KM3NeT optical module. This procedure should include: - an approved list of specification, - the definition of the test procedures necessary to characterize the different prototypes, - the selection criteria required to identify the "best" design. It is important that all ideas and solutions so far developed will be presented at the meeting as well as the most recent results from simulations of the possible detector geometries and the present concepts of the data handling and transmission.

Wednesday, 9 April

REGISTRATION

12:00 LUNCH IN CAFETERIA

WELCOME

SESSION I - Presentation/Round table with WP2

1 Status of simulations

Speaker: D. Dornic

Slides Optical_Module_Specifications2.ppt

2 Optical Modules in the KM3NeT optimization studies in Erlangen

Speaker: R. Shanidze

Slides OMv2_Shanidze.ppt

3 Simulations with directional optical module

Speaker: V. Kulikovsky

Slides Kulikovskiy_april-2008.pdf

16:00 COFFEE BREAK

4 Discussion

Thursday, 10 April

SESSION II - Review of PMT's

For the different solutions, speakers will have to describe the proposed
solution, the advantages and drawbacks, the results obtained, the plans for future if any.

5 The ANTARES PMT

Speaker: S. Henry

Slides ANTARES_TYPE_PMT_-_Henry.ppt

6 X-HPD

Speaker: G. Hallewell

Slides WP3_meeting_0408_final__Hallewell.ppt

7 Directional OM

Speaker: A. Bersani

Slides 4-2008-OM-km3net_-_Bersani.ppt

8 Multi PMTs

Speaker: P. Koojman

Slides kooijman-Multi-PMT.ppt

11:00 COFFEE BREAK

SESSION III - Components/Interfaces of OM's

In addition of the PMT(s) what is inside the OM: base, electronics, optics...
Communication with outside world: connector(s), copper or copper/fibre...
What are the slow control needs, what is the acceptable consumption ?

9 Low Power Multi-Dynamics Front End Architecture for the Optical Module of a Neutrino Underwater Telescope

Speaker: D. Lo Presti

Slides Km3Net_WP3_Ge_LoPresti.ppt

10 Scott - A Front End Electronics readout for the KM3NET design

Speaker: F. Guillox

Slides KM3NET_V2_090408.ppt

11 Read out and transmission technologies for optical modules

Speaker: J. Hogenbirk

Slides NodenetworkGenua_2008_04_08-_Hogenbirk.ppt

12 Power dissipation properties of 17 glass spheres

Speaker: P. VERNIN

13:15 LUNCH IN CAFETERIA

SESSION IV - Towards the choice

In the spirit of the CDR we have to define how we can reach the design goals
including

Lifetime, Energy range, Zenith angular acceptance, Angular resolution of
detector, Time and position resolution, Charge dynamic range, Two-hit time
separation, Coincidences, Dark noise rate

Failure rate of optical modules.

This task would require the definition of the specifications, aiming at a
sort of common data sheet for the proposed solutions
What are the quantities to be measured?
How to measure and who?
Rules for the choice

list of actions WP3_Genova_Meeting_Summary.xls

13 What we learnt from the ANTARES experience

Speaker: S. Henry

Slides What_We_Learn_from_ANTARES_2.ppt

14 PMT measurement

Speaker: H. Loehner

Slides Multi-PMT-OM-GenuaHL.ppt

15 PMT tests in Erlangen

Speaker: O. Kalekin

Slides WP3_Kalekin_Genua2.ppt

16:00 COFFEE BREAK

16 Open discussion

Friday, 11 April

SESSION IV - Towards the choice

list of actions Activities.jpg Procedures.jpg

pictures close_out.jpg

17 Future PMT testing activities at APC

Speaker: B. Baret

18 The Genova testing facility

Speaker: H. Costantini

19 Discussion

13:00 END OF MEETING